自動在線V槽
分板機型“V”槽分板機對分板質量有更進一步的提高；可實現V槽X,Y雙方向自動分切，對分切鋁基板（300-1500MM)、銅基板、FR4、玻纖板分裁干凈無毛刺，分板機可以接駁流水線實現全自動分板無需人工放板；分切好的板經流水動運走大大節省人力，完全實現無人化分板作業。變換產品時直接換取刀模部分無需人工去慢慢調刀大大節省時間。
The automatic on-line V-slot dividing machine can further improve the quality of V-slot, and can realize the V-slot X-slot, Y two direction automatic cutting, cutting aluminum substrate (300-1500mm), copper substrate, FR4, fiberglass board is clean without burr. The board splitter can be connected to the assembly line to realize automatic plate separation without manual plate placement. The sliced plate is transported by flow, which greatly saves manpower and completely realizes humanized plate splitting operation. When changing the products, it is not necessary to adjust the tool slowly and save time.
1、設備用于單組多刀自動分板，根據不同產品制作不同的模。且更換產品方便快捷。
The equipment is used for single group multi knife automatic plate division, and different dies are made according to different products. And the replacement of products is convenient and fast.
2、電氣控制部分可在人機界面選擇即可實現，方便開啟或屏蔽；
The electrical control part can be selected in the man-machine interface, which is convenient to open or shield;
3、有人機界面，臺面上采用光幕形式及亞克力罩，確保安全
It has man-machine interface, light curtain and acrylic cover are used on the table to ensure safety
4、分板刀模下面有集塵托盤（可以根據客戶要求加裝吸塵裝置）
There is a dust collecting tray under the parting die (dust collection device can be installed according to customer requirements)
5、整體采用落地式結構，設備適用于所有帶V槽的拼板
The whole body adopts floor type structure, and the equipment is suitable for all panel with V groove
6、分切長度：長度小于400的V槽拼板，分切厚度：0.5～3.5 MM，分切拼板寬度6-240ＭＭ
Slitting length: V-slot panel with length less than 400, cutting thickness: 0.5-3.5 mm, cutting width: 6-240mm
7、分切材質：纖維板、鋁基板、銅基板
Cutting materials: fiberboard, aluminum substrate, copper substrate
8、刀模精度： +0.1MM，刀模壽命：50萬次以上
The accuracy of the die is + 0.1mm, and the service life of the die is more than 500000 times
9、數據監控系統：開機時間監控，產能監控，設備故障信息及自動排異系統等.
Data monitoring system: startup time monitoring, capacity monitoring, equipment fault information and automatic rejection system
10、分板工作方式：采用送板機或直接吸盤對接流水線，將PCBA送入或吸入分板模上，裝模后通過設定的程式路線，按PCBA拼板的V槽走完。分切完后通過吸盤裝產品和費料邊同時吸走。費料邊到費料框上送入，產品送入流水線上的盤子內送走。循環作業完全實現無人化生產。
Working mode: the PCBA is fed or sucked into the parting die by using a feeder or a direct sucker docking assembly line. After the die is installed, the PCBA is completed according to the V-groove of PCBA panel assembly through the set program route. After slitting, the product is loaded with suction cup and the waste material edge is sucked away at the same time. The waste material is sent to the waste material frame, and the product is sent to the plate on the assembly line. The cycle operation completely realizes unmanned production.
手推式PCB分板機介紹
Introduction of hand push PCB splitter
1.手動分板機，不是自動分板機和氣動分板機，它所采用的動力不依靠電動和氣動，僅僅依靠人力。一般手推式PCB分板機都會采用走刀式輕量化規劃，所以其在實際生產中操作起來非常安全和簡便。
Manual splitter is not automatic and pneumatic. Its power does not rely on electric and pneumatic, but only depends on human power. Generally, the hand push type PCB splitter will adopt the tool feeding lightweight planning, so it is very safe and easy to operate in the actual production.
2.手推式PCB分板機一般適用于V-CUT槽的SMD器件PCB板，相對傳統手掰分板方式，手推式PCB分板機在在整個的分切板的過程中，可以使板材不動，利用圓刀的滑移，手控直刀滑移速度，可調校V槽導向裝置高低，實現零件跨越V槽，快捷地適應不同厚度的基板，將切板識所產生的內應力降低，從而可以確保基板上的電子元件因為滑移的原因而導致錫裂等損壞。
Hand push PCB splitter is generally suitable for SMD PCB with V-CUT slot. Compared with the traditional manual breaking method, the manual PCB splitter can keep the board still in the whole process of cutting board. It can adjust the V-groove guiding device height by using the sliding of round knife and manual control of straight knife sliding speed, so as to realize parts across V-slot, quickly adapt to different thickness of substrate, and recognize the production of cutting board The internal stress is reduced, so as to ensure that the electronic components on the substrate are damaged due to the slip.
3.另外，手推式PCB分板機是以手推式進行PCB的分板，不需要使用馬達，這樣就不會產生靜電振動和粉塵噪音等，而且一般手推式PCB分板機都比較小巧，可以節省工作空間，同時由于是手動操作，不需要電源，在優化環境和節省能源的同時還能精確控制PCB分板的精度，尤其是小型高精度的PCB板分割。
In addition, the manual PCB splitter uses the hand push type to divide the PCB, and does not need to use the motor, so it will not produce static vibration and dust noise. Moreover, the general hand push PCB splitter is relatively small, which can save working space. At the same time, because it is manual operation, it does not need power supply. It can optimize the environment and save energy, and can accurately control the accuracy of PCB board, In particular, small high-precision PCB board segmentation.
中文版 
English1
